Views: 63 Author: Site Editor Publish Time: 08-09-2021 Origin: Site
Because the laser cleaning machine has the cleaning characteristics of non-grinding, non-contact, non-thermal effect and suitable for objects of various materials, it is considered to be the most reliable and effective cleaning solution. At the same time, the laser cleaning machine can solve the problems that cannot be solved by traditional cleaning methods. Therefore, the use of laser cleaners in the industry is becoming more and more extensive. So, what matters should be paid attention to during the use of laser cleaners? Today Leapion Laser will share with you.
When starting up, turn on the water pump (water cooler) first, then turn on the power switch, and then turn on the laser switch. When shutting down, turn off the laser switch first, then turn off the power switch, and then turn off the water pump (water cooler).
1) Because the water in the chiller will become dirty, it will affect the light output, so clean the chiller of the laser machine regularly every half a month to drain the visceral water, and then fill it with new pure water or distilled water;
2) According to the water quality, check whether the filter (laser and the filter of the water chiller) is blocked, check whether the filter element of the water cooler is polluted, and the water cooler filter element needs to be replaced once a maximum of six months.
During the operation of the laser cleaning machine, a large amount of corrosive dust and smoke will be generated during the processing of the processed parts. If these smoke and dust are deposited on the surface of the guide rail and linear axis for a long time, it will have a great impact on the processing accuracy of the equipment. And it will form corrosion spots on the surface of the linear axis of the guide rail, shortening the service life of the equipment. In order to make the machine work normally and stably and ensure the processing quality of the products, the daily maintenance of the guide rail and linear axis must be done carefully.
It is required to clean regularly and quantitatively every day, remove the debris on the table, stopper and guide rail, and spray lubricating oil on the guide rail and linear rail.
The reflector and focusing lens should be scrubbed with a special cleaning solution every 6-8 hours. When scrubbing, use a cotton swab or cotton swab dipped in the cleaning solution to scrub in a counterclockwise direction from the center to the edge of the focusing lens. At the same time, be careful not to scratch the lens.
When there is a lot of smoke and dust during processing, it is necessary to clean the fan, remove the cover of the fan, use thin wood to scrape the dust on the fan blades and the wind channel, and then use a high-pressure gun to blow off the dust, and the method of cleaning the smoke pipe and The water cleaning method of the exhaust fan is the same.
1) After the laser has been running for 2000 hours, replace the vacuum pump oil, clean or replace the vacuum pump filter element.
2) After the laser has been running for 5000 hours, it is necessary to lubricate the turbine bearings. One turbine has two bearings, two pipes of lubricating oil, and two turbines with four pipes of lubricating oil. If the turbine is running loudly, the turbine bearing needs to be replaced.
3.) Keep the laser clean, and wipe the dust on the resonator (glass tube, cathode aluminum block, bakelite) twice a month. Dust is caused by electrostatic adsorption. If it is not wiped in time, the dust will accumulate to a certain extent, which will cause high-voltage short circuit and cause serious damage to the laser. It is also very troublesome to repair. It is hoped that it will be taken seriously.
At the same time, wipe the dust on other parts inside the laser.
4) Pay attention to prevent condensation
When the laser is running in summer or in an environment with high humidity, the set temperature of the chiller needs to be adjusted according to the environmental humidity. The specific temperature setting can refer to the manual.
5) Pay attention to antifreeze in winter
When the ambient temperature is between minus 10 degrees Celsius and 0 degrees Celsius, antifreeze must be used and replaced every two months.
When the ambient temperature is lower than minus 10 degrees Celsius, a water chiller with dual function must be used and the cooling system must run uninterruptedly.
6) Lightning protection
In areas with frequent thunderstorms, it is necessary to prevent lightning strikes from damaging the laser. Try to avoid working the laser and cut off the power supply during a thunderstorm; if it is necessary to ensure that the grounding of the plant meets the standard when working in a thunderstorm, it is strictly forbidden to use iron rods or steel beams instead of grounding.
It can be seen that there are still many things we need to pay attention to when using a laser cleaning machine. Only in the process of operation and use, pay attention to the maintenance and maintenance of the laser cleaning machine, in order to extend the service life of the laser cleaning machine, thereby saving costs and creating greater benefits. For more questions about laser cleaners, please contact Leapion Laser.
