Laser cutting machine
You are here: Home / News / 13 small details to teach you how to use laser cutting machine safely

13 small details to teach you how to use laser cutting machine safely

Views:0     Author:heyu     Publish Time: 2020-05-28      Origin:Leapion fiber laser cutting machine

  Under the control of the computer, the laser is discharged by pulse, so as to output the controlled repetitive high frequency pulse laser, forming a beam with a certain frequency and a certain pulse width. The pulse laser beam is conducted and reflected through the optical path and focused on the surface of the processed object through the focus lens group, forming a fine, high-energy density spot near the surface to be processed, To melt or vaporize the processed material at an instant high temperature.

  Every high-energy laser pulse can splash a small hole on the surface of the object in an instant. Under the control of computer, the laser cutting head and the material to be processed move continuously and relative to each other according to the pre drawn figure, so that the object can be processed into the desired shape.

  When the laser cutting equipment is working, if it breaks down, it is very dangerous. The novice must be trained by professional personnel to operate independently. Here are 13 details about the safe work of the laser cutting machine.

  1. Observe the safety operation regulations of general cutter. Start the laser in strict accordance with the laser startup procedure;

  2. The operator must be trained, familiar with the structure and performance of the equipment, and master the relevant knowledge of the operating system;

  3. Wear labor protection articles as required, and wear protective glasses that meet the requirements near the laser beam;

  4. Do not process a material before making sure whether it can be irradiated or heated by laser, so as to avoid the potential danger of smoke and steam;

  5. When the equipment is started, the operator shall not leave the post or be entrusted to be managed without permission. If it is really necessary to leave, the operator shall shut down or cut off the power switch;

  6. Put the fire extinguisher in the accessible place; turn off the laser or shutter when not processing; do not place paper, cloth or other inflammables near the unprotected laser beam;

  7. If any abnormality is found during the processing, the machine shall be shut down immediately, the fault shall be eliminated in time or the technical personnel shall be contacted for handling;

  8. Keep the laser, bed and surrounding areas clean, orderly and free of oil pollution, and stack the workpieces, plates and wastes as required;

  9. When using gas cylinder, avoid crushing the welding wire to avoid leakage accident. The use and transportation of gas cylinders shall comply with the supervision regulations of gas cylinders. Cylinders shall not be exposed to the sun or near the heat source. When opening the bottle valve, the operator must stand at the side of the bottle mouth;

  10. High pressure safety regulations shall be observed during maintenance. Every 40 hours of operation or weekly maintenance, every 1000 hours of operation or every six months of maintenance, in accordance with the regulations and procedures;

  11. Start the machine manually in X and Y directions at low speed after startup, and check whether there is any abnormality;

  12. After inputting the new workpiece program, it is necessary to test run it first and check its operation;

  13. During operation, pay attention to the operation of the machine tool and the gantry travel, so as to adjust in time.

  The above is the small details of laser cutting machine used by leapion for you. You can also contact our after-sales service personnel to ask about the use of laser cutting machine. Our technical personnel will give you the most professional answers.


LASER Product Recommendations

The data are for reference only

  •  

LC Laser Cutting
& Engraving Machine

LC-MN Laser Cutting
& Engraving Machine
LF-ST Dual-use Sheet & Tube
Fiber Laser Cutting Machine
LF-H Flatbed Fiber Laser
Cutting Machine
LF-STE Double platforms Sheet & Tube
Fiber Laser Cutting Machine
LF-STP Enclosed Sheet & Tube
Fiber Laser Cutting Machine
LF-E Entry-level Economy
Fiber Laser Cutting Machine
LF-Mi High Precision
Fiber Laser Cutting Machine
LF-PE Enclosed Protective
Fiber Laser Cutting Machine
LF-T Tube fiber laser cutting machine
LC-Mi-Mini-Laser-Engraving

LF-EX Exchange Platform
Fiber Laser Cutting Machine

LF-AT-Automatic-loading-tube

About Us

Contact Us

  Tel : +86-531-8898-2620
   Email : info@leapion.com
Copyright  2019 Shandong Leapion Machinery Co,.Ltd.  All Rights Reserved.